Crocheting a hat “in the round” sounds tricky, but it’s really just a flat circle that turns into a tube. Once you understand the formula, you can make a crochet beanie in the round in any size — newborn to adult XL — without a pattern. This tutorial gives you 7 clear steps and a free size chart.
What you need
- 100 g worsted (#4) yarn (adult size)
- 5.5 mm (US I-9) hook
- Stitch marker, yarn needle, tape measure
Abbreviations (US): ch, sl st, hdc = half double crochet, 2hdc = 2 hdc in the same stitch, st(s), rnd.
The size chart
| Size | Head circumference | Crown diameter | Total hat height |
|---|---|---|---|
| Newborn | 33–36 cm | 10.5 cm | 13–15 cm |
| Baby 3–6 m | 36–41 cm | 11.5 cm | 15–16.5 cm |
| Baby 6–12 m | 41–46 cm | 13 cm | 16.5–18 cm |
| Toddler | 46–48 cm | 14 cm | 18–19 cm |
| Child | 48–51 cm | 15 cm | 19–20 cm |
| Teen / Adult S | 51–56 cm | 16.5 cm | 20–21.5 cm |
| Adult M | 56–58 cm | 17.5 cm | 21.5–23 cm |
| Adult L | 58–61 cm | 18.5 cm | 23–25 cm |
The magic formula: crown diameter = (head circumference − 2.5 cm) ÷ 3.14. That’s why the chart works for any yarn.
Step 1: Make a gauge swatch
Work a few rows of hdc and measure how many stitches fit in 10 cm. You’ll use this later to check your circle. (It’s the step everyone skips — and the reason hats don’t fit!)
Step 2: Start the crown
- Ch 2. Work 10 hdc in the 2nd ch from the hook (or use a magic ring). Join with sl st to the first hdc. (10)
Step 3: Increase rounds
Each round adds 10 stitches.
- Rnd 2: ch 1, 2hdc in each st. Join. (20)
- Rnd 3: ch 1, hdc, 2hdc around. Join. (30)
- Rnd 4: 2 hdc, 2hdc around. (40)
- Rnd 5: 3 hdc, 2hdc around. (50)
- Rnd 6: 4 hdc, 2hdc around. (60)
- Keep going (one more hdc between increases each round) until the circle reaches your crown diameter.
Why does my hat ruffle? Too many increases or a tight gauge. If the circle waves, rip back one round. If it cups like a bowl, add one increase round.
Step 4: Work even
Stop increasing. Work hdc in each stitch around, joining each round, until the hat measures your total height minus 5 cm from the crown.
Step 5: Make the brim
Switch to a ribbed stitch for stretch:
- front post hdc, back post hdc around for 4–5 rounds.
Step 6: Try it on
The hat should feel snug, not tight. Too short? Add rounds before the brim.
Step 7: Finish
Fasten off and weave in the ends. Add a pom-pom, a leather tag or a folded brim.
Joined rounds vs spiral
| Method | Pros | Cons |
|---|---|---|
| Joined rounds (this tutorial) | neat stripes, easy counting | visible seam line |
| Spiral (no join) | invisible seam | stripes “jog”; use a marker |
Troubleshooting
- Seam leans: turn your work at the end of each round to keep it straight.
- Hat too loose: go down a hook size or remove 10 stitches (one increase round).
- Brim flares: work the brim with a hook 0.5 mm smaller.
FAQ
Is it easier to crochet a beanie in the round or flat?
Flat is easier for total beginners (see our ribbed master beanie), but in the round needs no seam and is better for stripes.
How many stitches for an adult beanie?
With worsted and hdc, usually 60–70 stitches around for adult M — but always follow the crown diameter, not the number.
Can I use this chart for any yarn?
Yes. Diameter and height are measurements, so they work with any yarn weight.
Next steps
Save this chart! Pin it to your Crochet Hats for Beginners board so it’s there every time you start a new hat — and find more tutorials on Crochetips.




